Hello,Welcome!   [Login] [Register] sitemaps |  Board |  Collection site | Order Online | wholesale
We will confirm with you before delivery.
vedio center products center Honor Knowledge Outstanding Articles
Your Position: > Knowledge >> Electro Acupuncture >>> Instruction of BL-F Electro Acupuncture

Instruction of BL-F Electro Acupuncture

Bluelight / 2011-02-21
[B] [M] [S]

Click here to see the BL-F product information

 


1. Power Switch

2. Numeral Screen

3. Start /Pause Button

4. Setting Button

5. Up Button

6. Down Button

7. Jack of treating in Electric Intensity II

8. Jack of Heat Intensity

9. Jack of Electromagnetism Contactor

10. Jack of Electrode Slice in Electric intensity I

11. Signal-output Plug of Electromagnetism Contactor

12. Electromagnetism Contactor in Electric Intensity I

13. Plug of Electrode Slice

14. Electrode Slice

15. Heat Treatment slice

16. Plug of Electric Intensity II

17. Plug of Heat Treatment

 

Instruction of BL-F Electro Acupuncture 

1. Choosing Treatment Methods

The treating methods are listed as below:

A. Electromagnetism Contactor Therapy  B. Electrode Slice Therapy

C. Multifunctional Radiation treating Board Therapy  D. Far Infrared Heat Therapy

“Electric Intensity I” on the numeral screen controls therapeutic method A and B

“Electric Intensity II” on the numeral screen controls therapeutic method C

“Heat Intensity” on the numeral screen controls therapeutic method D

All the above treatments A, B, C, D can work separately or simultaneously.

 

2. Preparations:

(1) For Electromagnetism Contactor therapy in Electric Intensity I: wrap the two Electromagnetism Contactors (12) with 3-tiered gauzes and bind each of them with a piece of elastic, soak them with water, insert the two Signal-output Plug (11) into the Jack of Electromagnetism Contactor (9).

(2) For Electrode Slice Therapy: Insert the Plug of Electrode Slice (13) into the Jack of Electrode Slice in Electric Intensity I (10), uncover the patch and put it on the treating part, (Caution: do not touch water.)

(3) For Multifunctional Radiation Treating Board Therapy: put the Multifunctional Radiation Treating Board (15) on the treating points after soaking it with water, and then insert the Plug of Electric Intensity II (16) into Jack of treating in Electric Intensity II (7) and fially insert the Plug of Heat Treatment (17) into Jack of Heat Intensity (8).

(4) For Apparatus: check the Power Switch and make it in power-off position, connect apparatus with the power source.

 

3. Operation steps

(1) Find the acupoints, press the Power Switch (1) and the Numeral Screen (2) would turn light.

(2) Press Start/Pause Button (3) after hearing the alarm sounds, then the four luminous spots on the right bottom of Numeral Screen (2) start to flash. Treatment started and treatment time shown on the screen was counting-down. Press Start/Pause Button (3) to stop it when Pausing is needed, press the same button to restart it, the treatment time will be memorized and continuously counted down after the restart.

(3) Time setting: press Setting Button (4) till the number of Timing on Screen (2) flashes, press Up Button (5) to add the treatment time or press Down Button (6) to reduce the treatment time.(Do not set the number of Timing as 0, or the apparatus would not work)

Treating methods A or B: press Setting Button (4) till the number of the Electric Intensity I on Screen (2) flashes, press Up Button (5) to add electric intensity, or press Down Button (6) to reduce electric intensity.

Treating method C: press Setting Button (4) till the number of Electric Intensity II on the Screen (2) flashed, press Up Button (5) to add electric intensity, or press Down Button (6) to reduce electric intensity.

Treating methods D: press setting Button (4) till the number of Heat Intensity on the Screen (2) flashes, press Up Button (5) to add Heat Treatment intensity, it is suggested the number of Heat Intensity to be set as 3-5 range.

Pressing Setting Button (4) continuously, the number visions corresponding with Timing, Electric Intensity I, Electric Intensity II and Heat Intensity (from right to left) would flash in turn, you can choose any treatment methods as you like. During the treatment, you can change treatment methods in the same way.

 

4. Attentions

(1) For safety purpose, do not use the apparatus inside cotton bedcover, nor make warm through the Multifunctional Radiation Treating board.

(2) The pad on Electrode Slice in Electric intensity II should not be too dry in order to avoid affecting the conductivity.

(3) All the channels of body form a circulation upon the touch of the contactor or Electrode Slice. If you feel gentle tumefaction, slight tingle, tremulous in some sensitive acupoints, it means you have got the right acupoints and are curing the disease properly. If you feel uncomfortable tingle or aching, it means that the acupoints might not be correct, you should move the Electrode Slice or Electromagnetism Contactor, find the correct acupoints, and restart the treatment.

(4) Do not place the Electrode Slice or Electromagnetism Contactor on any injury skin to avoid current scalding or cross infection.

(5) It is normal that you might feel different intensity about the two Electrodes Slices or two Electromagnetism Contactors (Yin&Yang) and would not affect the curative effect.

(6) Keep a distance between the two Electrode Slice or Electromagnetism Contactors. Direct touch might cause short circuit, then the biology energy could not enter the human body and diseases could not be cured. Apparatus damaged in this way should be responsible by yourself.

(7) Dementia or mental disorder patients could only use the apparatus under the supervision of his family. People got bruise injury or acute wrench should use the apparatus 24 hours later.

(8) Patients got coma, pregnant, wearing metal accessory, active bleeding, cardiopulmonary function failure or wearing heart pacemaker are forbidden to use the apparatus.

(9) Do not pull the Heat Treatment Bag in order to prevent the breaking of the spiral Electric wire.

(10) The hood of the Heat Treatment Bag can be removed for washing if it is dirty and used again until dry.

(11) Calenture, drying disease, fever patients should not start the heat therapy but use the Electromagnetism Contactor, or set the heat intensity at 0, and then use Multifunctional Radiation Treating Board.

(12) In Numeral Screen, the largest number of time is 9 and the largest of Electricity Intensity I, II and Heat Intensity are 8. If the time is 0, the apparatus will not work and treatment could not go on. The apparatus could only work when the time is set above 0.

(13) Press Up or Down Button four times to add or reduce one intensity grade of Electric Intensity I, II; and press Up or Down Button one time to add or reduce one grade of time and Heat Intensity.

 

5.Some Tips:

(1) Inset all fitting plugs needed before the treatment, and do not remove them while the treatment is processing, or it might spoil the apparatus performance.

(2) Please remove power plug to save electricity after the treatment.
 

User Comment

No comment
Username: Anonymous user
E-mail:
Rank:
Content:
Verification code: captcha
                        

Products  |  Bluelight History  |  Culture  |  About Us  |  Honor  |  Knowledge  |  Joining  |  Feedback  |  Service  |  Company profile  |  Sitemap  |  wholesale
© 2005-2024 blue-light Copyright, All Rights Reserved.
13th floor, Zhongli Enterprise Building No.92 Xudong Rd, Wuhan City, Hubei, China. Tel: 0086 27-86826688 86836688 0086-13720350106
E-mail: global@e-bluelight.com MSN 2412549315 cn209788248

Run 69 queries, spents 0.181654 seconds, 20 people online,Gzip enabled,take up memory 3.780 MB
客 服 中 心 Customer Service